한국생산제조학회 학술지 영문 홈페이지
[ Best Paper of This Month ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 31, No. 4, pp.225-232
ISSN: 2508-5107 (Online)
Print publication date 15 Aug 2022
Received 06 Jun 2022 Revised 28 Jul 2022 Accepted 29 Jul 2022
DOI: https://doi.org/10.7735/ksmte.2022.31.4.225

CNC 공작기계의 고정밀 윤곽가공을 위한 가변 윤곽오차 모델

정성윤a ; 강정모a ; 지성철a, *
Variable Contour Error Model for High-Precision Contour Machining of CNC Machine Tools
Sungyoun Junga ; Jeongmo Kanga ; Sungchul Jeea, *
aDepartment of Mechanical Engineering, Dankook University

Correspondence to: *Tel.: +82-31-8005-3504 E-mail address: scjee@dku.edu (Sungchul Jee).

Abstract

Studies have been conducted on various contour error models applied to cross-coupling control systems, which are essential for achieving contour accuracies in multi-axis CNC systems. Most of these studies examine contour error models for straight, corner, and curved tool paths. However, there are limitations to applying these existing works in multi-axis tool paths because the straight, corner, and curved tool paths may coexist. Therefore, this paper presents a variable contour error model for cross-coupling control systems to achieve high-precision contour machining. The proposed variable contour error model allows real-time changes to the contour error model based on the tool path curvature. The proposed model was evaluated by implementing a cross-coupling control system on a PC-based three-axis CNC testbed. From the experimental results, the usefulness of the proposed model was confirmed in terms of the contour accuracy.

Keywords:

CNC machine tool, High-precision machining, Cross-coupling controller, Variable contour error model, Contouring accuracy

Acknowledgments

이 연구는 2021년도 산업통산자원부 및 한국산업기술평가관리원(KEIT) 연구비 지원에 의한 연구임(20012834).

References

  • Makino, H., Ohde, T., 1991, Motion Control of the Direct Drive Actuator, CIRP Ann-Manuf. Technol., 40:1 375-378. [https://doi.org/10.1016/S0007-8506(07)62010-1]
  • Ono, Y., Kuwahara, H., 1986, The New Design of Motor, Position Sensor and Position Control System for Direct Drive Manipulators, Proc. ASME Robotics: Theory and Applications, 123-128.
  • Pritschow, G., Philipp, W., 1990, Direct Drives for High-Dynamic Machine Tool Axes, CIRP Ann-Manuf. Technol., 39:1 413-416. [https://doi.org/10.1016/S0007-8506(07)61085-3]
  • Schepper, F., Yamazaki, K., Shigemura, T., Imai, M., Hoshi, T., Development of an ASIC Performing High Speed Current Loop Processing of Servo Motor Control for Mechatronics Applications, CIRP Ann-Manuf. Technol., 38:1 355-358. [https://doi.org/10.1016/S0007-8506(07)62722-X]
  • Koren, Y., 1980, Cross-Coupled Biaxial Computer Control for Manufacturing Systems, J. Dyn. Sys., Meas., Control., 102:4 265-272. [https://doi.org/10.1115/1.3149612]
  • Lee, H. C., Jeon, G. J., 1999, Real-Time Compensation of Two-Dimensional Contour Error in CNC Machine Tools, IEEE/ASME International Conference on Advanced Intelligent Mechatronics, 623-628. [https://doi.org/10.1109/AIM.1999.803240]
  • Lo, C. C., Koren, Y., 1992, Evaluation of Servo-Controllers for Machine Tools, 1992 American Control Conf., 370-374. [https://doi.org/10.23919/ACC.1992.4792091]
  • Jee, S. C., Koo, T. H., 2004, 3-Axis Coupling Controller for High-Precision/High-Speed Contour Machining, Trans. Korean. Soc. Mech. Eng. A., 28:1 40-47. [https://doi.org/10.3795/KSME-A.2004.28.1.040]
  • Erkorkmaz, K., Yeung, C. -H., Altintas, Y., 2006, Virtual CNC System. Part II. High Speed Contouring Application, Int. J. Mach. Tools Manuf., 46:10 1124-1138. [https://doi.org/10.1016/j.ijmachtools.2005.08.001]
  • Yang, J., Altintas, Y., 2015, A Generalized On-line Estimation and Control of Five-Axis Contouring Errors of CNC Machine Tools, Int. J. Mach. Tools Manuf., 88 9-23. [https://doi.org/10.1016/j.ijmachtools.2014.08.004]
  • Sencer, B., Altintas, Y., Croft, E., 2009, Modeling and Control of Contouring Errors for Five-Axis Machine Tools-Part I: Modeling, J. Manuf. Sci. Eng., 131:3 031006. [https://doi.org/10.1115/1.3123335]
  • El Khalick, M. A., Uchiyama, N., 2013, Estimation of Tool Orientation Contour Errors for Five-Axis Machining, Robot. Comput.-Integr. Manuf., 29:5 271-277. [https://doi.org/10.1016/j.rcim.2013.01.002]
  • Chen, H. R., Cheng, M. Y., Wu, C. H., Su, K. H., 2016, Real Time Parameter Based Contour Error Estimation Algorithms for Free Form Contour Following, Int. J. Mach. Tools Manuf., 102 1-8. [https://doi.org/10.1016/j.ijmachtools.2015.11.009]
  • Lim, J. H., Jee, S. C., 2011, Improvement of Corner Contouring Accuracy of CNC Servo Systems with Communication Delay, J. Korean Soc. Precis. Eng., 28:2 168-175.
Sungyoun Jung

Master’s degree student in the Department of Mechanical Engineering, Dankook University. His research interest is CNC machine tool systems and artificial intelligence.

E-mail: sungyj@dankook.ac.kr

Jeongmo Kang

Ph.D. candidate in the Department of Mechanical Engineering, Dankook University. His research interest is CNC machine tool systems and CAD/CAM.

E-mail: jmkang@dankook.ac.kr

Sungchul Jee

Professor in the Department of Mechanical Engineering, Dankook University. His research interest is CNC machine tool systems and CAM.

E-mail: scjee@dku.edu