한국생산제조학회 학술지 영문 홈페이지
[ Technical Papers ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 28, No. 3, pp.181-187
ISSN: 2508-5107 (Online)
Print publication date 15 Jun 2019
Received 09 Apr 2019 Revised 17 May 2019 Accepted 27 May 2019
DOI: https://doi.org/10.7735/ksmte.2019.28.3.181

공압발전을 이용한 30W급 LED 방폭등 광학계 연구

강용주a, * ; 이창수a ; 유경선a ; 현동훈a
Study on 30W LED Explosion Proof Light Optical System Using Air Driver
Yong Ju Kanga, * ; Chang Soo Leea ; Kyung Sun Yooa ; Dong Hoon Hyuna
aGraduate School of Knowledge-based Technology & Energy (Opto-Nanotronics), Korea Polytechnic University, 237, Sangidaehak-ro, Siheung, Gyeonggi-do, 15073, Korea

Correspondence to: *Tel.: +82-31-8041-1784 Fax: +82-31-8041-1784 E-mail address: smart1890@ewp.co.kr (Yong Ju Kang).

Abstract

We propose an LED explosion-proof light for a generator-type ballast that produces electricity using air pressure to replace the ballast in current explosion-proof lighting. The lens of the LED explosion-proof light has an aspheric design, and its light distribution was analyzed to assess whether it could provide uniform brightness in the work place. The quantitative goal was achieved via optimization design. A prototype of the LED explosion-proof light with/containing an air driver was manufactured to verify the performance of the lens. Measurement results showed that the cd ratio and light distribution angle decreased, while the flux and efficiency increased as compared to the designed values. The surface roughness of the lens increased slightly, and the light distribution curve changed. As the quantitative target could achieve and reduce the weight, this can also contribute to the development of portable LED lighting with air drivers in the future.

Keywords:

LED, Air driver, Explosion proof, Aspheric, Lens, Optical system

References

  • Yeo, J. K., Kim, J. S., Yu, Y. M., 2017, Study on the Design and Lighting Characteristics of 150W LED Flood Lighting with Flameproof Enclosure, Journal of the Korean Institute of Illuminating and Electrical Installation Engineers, 31:1 1-15. [https://doi.org/10.5207/JIEIE.2017.31.11.001]
  • Song, O. D., Seok, J. K., Yu, Y. M., 2017, A Study on Zener Barrier Design and Electrical Characterization Experiment for 3W Intrinsic Safety Explosion-Proof LED Lighting, Journal of the Korean Institute of Illuminating and Electrical Installation Engineers, 31:12 94-104. [https://doi.org/10.5207/JIEIE.2017.31.12.094]
  • Choi, S. W., 2013, A Study on the Light Weight Hand Lamp for Explosion-Proof Type, Journal of the Korean Society of Safety, 28:2 31-36. [https://doi.org/10.14346/JKOSOS.2013.28.2.031]
  • Kasahara, T., Aizawa, D., Irikura, T., Moriyama, T., Toda, M., Iwamoto, M., 2006, Discomfort Glare Caused by White LED Light Sources, Journal of Light & Visual Environment, 30:2 95-103. [https://doi.org/10.2150/jlve.30.95]
  • Shei, S. C., Lin, N. M., Chang, S. J., Wu, Y. X., 2011, Optical Design of A Freeform Lens Based on Multi-Chip-on-Single-Board LED Light Source for 140W Street Lamp, International Journal of Science and Engineering, 1:1 31-33.
  • Kim, D. J., Yoo, K. S., Hyun. D. H., 2010, An Research on Ultra Precisive Polishing Manufacturing Technology of Glass for Micromini and Super Wide-Angle Aspherics Glasses Lens, Journal of Korean Society of Manufacturing Technology Engineers, 19:2 275-281.
  • KS, 2016, Tempered Glasses, KS L 2002, Korean Agency for Technology and Standards, Korea.
  • Lee, C. S., Lee, S. Y., Hyun. D. H., 2017, Analysis of Performance on Asymmetric LED Lens Design Using Three-Dimensional Free-Form Surface Expression, Journal of Korean Society of Manufacturing Technology Engineers, 26:3 328-336. [https://doi.org/10.7735/ksmte.2017.26.3.328]
  • Lee, S. J. 2007, A Study on the Manufacturing Process for Pick up Lens, Doctorate thesis, Korea Polytechnic University, Republic of Korea.
  • Yoo, K. S., Lee, C. S., Hyun. D. H., 2014, Investigation of the Angular Distribution of Luminous Intensity in the Symmetric Optical System of a COB LED High Bay, Journal of Korean Society of Manufacturing Technology Engineers, 23:6 609-617. [https://doi.org/10.7735/ksmte.2014.23.6.609]