Your browser does not support the PubReader view.
Go to this page to see a list of supporting browsers.
한국생산제조학회 학술지 영문 홈페이지
[ Technical Papers ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 32, No. 1, pp.42-48
ISSN: 2508-5107 (Online)
Print publication date 15 Feb 2023
Received 21 Dec 2022 Revised 12 Jan 2023 Accepted 13 Jan 2023
DOI: https://doi.org/10.7735/ksmte.2023.32.1.42

SLA 기반 LCD 3D 프린터 제작에 관한 연구

성시헌a ; 이성범b, * ; 김현철c, *
Manufacturing of Stereolithography-based Liquid Crystal Display Three-dimensional Printer
Siheon Seonga ; Seongbeom Leeb, * ; Hyunchul Kimc, *
aDepartment of Mechanical Engineering, Inje University
bDepartment of Electronic, Telecommunications, Mechanical and Automotive Engineering, High Safety Vehicle Core Technology Research Center, Inje University
cDepartment of Future Automotive Engineering, Kongju National University

Correspondence to: b*Tel.: +82-55-320-3667 E-mail address: mechlsb@inje.ac.kr (Seongbeom Lee).Correspondence to : c*Tel.: +82-41-521-9273 E-mail address: khc@kongju.ac.kr (Hyunchul Kim). * These authors contributed equally to this work.

Abstract

With the development of the Fourth Industrial Revolution, the use of three-dimensional (3D) printers has drawn attention as an approach to supplementing the limitations of mold processing by reducing various materials, complex shapes, and discontinuation cycles. However, there are limits to its application because its extended manufacturing time and expensive equipment do not satisfy the efficiency requirements of the existing mold method. This paper presents a method for solving the problems of existing 3D printers by producing liquid crystal display 3D printers with low cost, high manufacturing speed, and high precision. And for the verification, products of various shapes were printed and evaluated.

Keywords:

3D Printer, Liquid crystal display (LCD), Light emitting diode (LED), Design method, Production

Acknowledgments

이 논문은 2021년도 정부(과학기술정보통신부)의 재원으로 정보통신기획평가원의 지원(No. 2021-0-00447, 30%)과 2021~2022년도 교육부의 재원으로 한국연구재단의 지원을 받아 수행된 지자체-대학 협력 기반 지역혁신 사업의 결과입니다. (2021RIS-003, 2021RIS-004, 70%)

References

  • Choi, B. J., Yang, J. Y., Lee, M. G., Jeon, Y. H., 2021, Defect Analysis of Metal 3D Printing Process, J. Korean Soc. Manuf.Technol. Eng., 30:1 92-98. [https://doi.org/10.7735/ksmte.2021.30.1.92]
  • Jung, C. H., Lee, M. G., Jeon, Y. H., 2021, Metal 3D Printing Simulation through Thermal-structure Coupled Numerical Analysis, J. Korean Soc. Manuf. Technol. Eng., 30:5 389-395. [https://doi.org/10.7735/ksmte.2021.30.5.389]
  • Choi, E. J., Kim, S. A., Bae, J. Y., Lee, K. H., 2013, A Study on the State-of-the-Art of 3D Printers, Proceedings of the Korean Society of Computer Information Conference, 21:2 385-388.
  • Lee, J. J., 2016, 3D Printing for Biomedical Use Technology Utilization and Prospects, The Magazine of the IEIE, 43:8 20-29, http://www.koreascience.or.kr/article/JAKO201626542339747.page, .
  • Shin, G. S., Kweon, H. K., Kang, Y. G., 2017, The Influence of Experiment Variables on DLP 3D Printing using ART Resin, J. Korean Soc. Manuf. Proc. Eng., 16:6 101-108. [https://doi.org/10.14775/ksmpe.2017.16.6.101]
  • Jang, M., Oh, A. S., 2017, Design of 3D Printer Based on SLA Using LSU and Test of Scanning Mechanism, Journal of the Korea Institute of Information and Communication Engineering, 21:6 1225-1230. [https://doi.org/10.6109/jkiice.2017.21.6.1225]
  • Jo, K. H., Lee, S. H., Jang, H. S., Ha, Y. M., 2015, Development of 3D Printer Using LCD and UV-LED, Proc. Korean Soc. Precis. Eng. Autumn Conf. 2015, 607-608.
  • Gupta, P., Bhat, M., Khamkar, V., Tandel, G., Salunkhe, G., 2020, Designing of Cost Effective Resin 3D Printer using UV LED, International Conference on Convergence to Digital World-Quo Vadis (ICCDW), 1-4. [https://doi.org/10.1109/iccdw45521.2020.9318691]
  • Quan, H., Zhang, T., Xu, H., Luo, S., Nie, J., Zhu, Xi., 2020, Photo-curing 3D Printing Technique and its Challenges, Bioactive Materials, 5:1 110-115. [https://doi.org/10.1016/j.bioactmat.2019.12.003]
  • Piedra-Cascón, W., Krishnamurthy, V., Att, W., Revilla-León, M., 2021, 3D Printing Parameters, Supporting Structures, Slicing, and Post-processing Procedures of Vat-polymerization Additive Manufacturing Technologies, J. Dent., 109 103630. [https://doi.org/10.1016/j.jdent.2021.103630]
  • 3D printer store, n.d., viewed 31 January 2023, <https://3dprinterstore.co.kr/product/detail.html?product_no=243&cate_no=132&display_group=1, >.
Siheon Seong

Ma. D. Candidate in the School of Mechanical Engineering, Inje University. His research interest is Mechanical Engineering.

E-mail: ssh831@oasis.inje.ac.kr

Seongbeom Lee

Professor in the Department of Electronic, Telecommunications, Mechanical and Automotive Engineering, Inje University. His research interest is Mechanical Engineering.

E-mail: mechlsb@inje.ac.kr

Hyunchul Kim

Professor in the Department of Future Automotive Engineering, Kongju National University. His research interest is CAD/CAM and Precision Machining.

E-mail: khc@kongju.ac.kr