한국생산제조학회 학술지 영문 홈페이지

Current Issue

Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 29 , No. 4

[ Papers ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 29, No. 4, pp.288-295
Abbreviation: J. Korean Soc. Manuf. Technol. Eng.
ISSN: 2508-5107 (Online)
Print publication date 15 Aug 2020
Received 26 Mar 2020 Revised 20 May 2020 Accepted 26 May 2020
DOI: https://doi.org/10.7735/ksmte.2020.29.4.288

레이저 쇼크 패터닝을 통한 표면 텍스처링이 알루미늄과 강 접촉면의 마찰특성에 미치는 영향
이성구a, ; 송경욱a, ; 최대철b ; 노종현a ; 김홍석a, *

Laser Shock Surface Patterning of Steel and Aluminum Contact Surfaces and its Effect on Tribological Properties
Sung Goo Leea, ; Kyeong Uk Songa, ; Dae Cheol Choib ; Jong Hyun Noha ; Hong Seok Kima, *
aDepartment of Mechanical and Automotive Engineering, Seoul National University of Science and Technology
bDepartment of Mechanical Engineering, Graduate School of Seoul National University of Science and Technology
Correspondence to : *Tel.: +82-2-970-6333 E-mail address: hongseok@seoultech.ac.kr (Hong Seok Kim).
These authors contributed equally to this work and are joint first authors.

Funding Information ▼

Abstract

In this study, a laser shock surface patterning process was applied to effectively transfer a micro-pattern array to an aluminum specimen. The effect of surface texturing on the tribological properties of aluminum and steel contact surfaces was investigated. In dry conditions, the friction coefficient of the contact surface could be significantly reduced through surface texturing. However, as the contact load increased, the amount of wear debris collected in the cavity became too large, and the influence of the micro-pattern on the frictional force decreased. In lubricated conditions, surface texturing significantly reduced the average friction coefficient and its variation. The effect of surface texturing became prominent in high contact load conditions due to the increase in hydrodynamic effects. Further studies considering the pattern geometry, loading conditions, and properties of the lubricant are needed to quantitatively model the coefficient of friction.


Keywords: Surface texturing, Laser shock patterning, Micro-pattern array, Friction, Aluminum alloy

Acknowledgments

이 연구는 서울과학기술대학교 교내 학술연구비 지원으로 수행되었습니다.


References
1. Flegler, F., Neuhauser, S., Groche, P., 2020, Influence of Sheet Metal Texture on the Adhesive Wear and Friction Behaviour of EN AW-5083 Aluminum Under Dry and Starved Lubrication, Tribol. Int., 141 105956.
2. Benea, L., Dumitrascu, V., 2019, Enhancement in Sustained Friction and Wear Resistance of Nanoporous Aluminum Oxide Films Obtained by Controlled Electrochemical Oxidation Process, RSC Adv., 9 25056-25063.
3. Wan, Y., Liu, W., Xue, Q., 1996, Effects of Diol Compounds on the Friction and Wear of Aluminum Alloy in a Lubricated Aluminum-on-steel Contact, Wear, 193 99-104.
4. Won, S. J., Kim, H. S., 2019, Effects of Laser Parameters on Morphological Change and Surface Properties of Aluminum Alloy in Masked Laser Surface Texturing, J. Manuf. Process., 48 260-269.
5. Shimizu, J., Nakayama, T., Watanabe, K., Yamamoto, T., Onuki, T., Ojima, H., Zhou, L., 2019, Friction Characteristics of Mechanically Microtextured Metal Surface in Dry Sliding, Tribol. Int., 105634.
6. Li, N., Xu, E., Liu, Z., Wang, X., Liu, L., 2016, Tuning Apparent Friction Coefficient by Controlled Patterning Bulk Metallic Glasses Surfaces, Sci. Rep., 6 1-9.
7. Zhang, J., Zhang, J., Rosenkranz, A., Suzuki, N., Shamoto, E., 2019, Frictional Properties of Surface Textures Fabricated on Hardened Steel by Elliptical Vibration Diamond Cutting, Precis. Eng., 59 66-72.
8. Li, S., Zhang, N., Yang, Z., Li, X., Zhao, G., Wang, T., Wang, Q., Zhang, X., 2019, Tailoring Friction Interface with Surface Texture for High-performance Ultrasonic Motor Friction Materials, Tribol. Int., 136 412-420.
9. Fiaschi, G., Di Lauro, M., Ballestrazzi, A., Rota, A., Biscarini, F., Valeri, S., 2019, Tribological Response of Laser-textured Steel Pins With Low-dimensional Micrometric Patterns, Tribol. Int., 105548.
10. Friedrich, C. R., 2002, Micromechanical Machining of High Aspect Ratio Prototypes, Microsyst. Technol., 8 343-347.
11. Singh, K., Varghese, S., Akhtar, J., 2015, Ultra Uniform Arrays of Micro Patterns on Large Area Substrate by Employing Wet Chemical Etching, Mater. Sci. Semicond. Process., 31 351-357.
12. Lee, J. H., Choi, D. C., Kim, H. S., 2018, Patterning and Characterization of Micro-dimple Arrays on Metallic Surfaces by Laser-accelerated Flyer Impact, J. Korean Soc. Manuf. Technol. Eng., 27:1 20-26.
13. Budynas, R. G., Nisbett, J. K., 2008, Shigley's Mechanical Engineering Design, McGraw-Hill, Singapore.
14. Choi, D. C., Kim, H. S., 2020, Performance Evaluation of Laser Shock Micro-patterning Process on Aluminum Surface with Various Process Parameters and Loading Schemes, Opt. Lasers Eng., 124 105799.

Sung Goo Lee

B.Sc. student in the Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology.His research interest is laser applications and tribology.

E-mail: lklk2091@gmail.com

Kyeong Uk Song

B.Sc. student in the Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology.His research interest is laser applications and tribology.

E-mail: yoog96@naver.com

Dae Cheol Choi

Ph.D. candidate in the Department of Mechanical Engineering, Seoul National University of Science and Technology.His research interest includes laser shock surface pattering and nanomaterials.

E-mail: cdc4662@seoultech.ac.kr

Jong Hyun Noh

B.Sc. student in the Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology.His research interest is laser applications and tribology.

E-mail: shwhdgus223@naver.com

Hong Seok Kim

Professor in the Department of Mechanical and Automotive Engineering, Seoul National University of Science and Technology.His research interest includes laser surface texturing, nanomaterials, and micro/nanoscale manufacturing.

E-mail: hongseok@seoultech.ac.kr