한국생산제조학회 학술지 영문 홈페이지

Journal Archive

Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 30 , No. 3

[ Best Paper of This Month ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 30, No. 3, pp. 169-173
Abbreviation: J. Korean Soc. Manuf. Technol. Eng.
ISSN: 2508-5107 (Online)
Print publication date 15 Jun 2021
Received 25 Feb 2021 Revised 16 Mar 2021 Accepted 17 Mar 2021
DOI: https://doi.org/10.7735/ksmte.2021.30.3.169

두 개의 성형공구를 이용한 무금형 6축 양면점진성형기 개발
최성주a ; 강재관b ; 김채환b, *

Development of a Dieless 6-Axis Double Side Incremental Forming Machine Using Two Forming Tools
Seong Ju Choia ; Jae Gwan Kangb ; Chai Hwan Kimb, *
aGraduate School of Mechanical Convergence Engineering, Kyungnam University
bSchool of Mechanical Engineering, Kyungnam University
Correspondence to : *Tel.: +82-55-249-6449 E-mail address: na48th@kyumgnam.ac.kr (Chai Hwan Kim).

Funding Information ▼

Abstract

Incremental sheet forming (ISF) does not use a partial or full die at the bottom of the die; rather, a hemispherical forming tool presses the sheet layer by layer along the numerically controlled movement path to cause plastic deformation. The ISF is somewhat limited in manufacturing freeform surfaces because the die is installed at the bottom of the sheet material. To compensate for these shortcomings, a double side incremental forming (DSIF) method, which can form both sides of the sheet simultaneously, is required with two independently controlled tools. This machine is composed of a forming part and support part, Equipped with a motion controller capable of 6-axis control, the developed DSIF machine can freely and smoothly form surfaces. To verify its performance, prototype forming was performed, and the 3D contact measurement and shape data were superimposed to compare and analyze the forming accuracy and verify the usefulness of incremental forming.


Keywords: Incremental sheet forming (ISF), Freeform surface, Incremental forming machine, Double side incremental forming (DSIF)

Acknowledgments

이 연구결과물은 2018학년도 경남대학교 대학특성화연구비 지원에 의한 것임.


References
1. Shim, M. S., Park, J. J., 2000, A Basic Study on Incremental Forming Method for Sheet Metal, Proceedings of the Korean Society for Technology of Plasticity Conference, 128-131.
2. Park, J. J., Kim, Y. H., 2003, A Study on Formability of Aluminum Sheet in Incremental Forming, Proc. KSME Spring Conf., 1142-1147.
3. Lee, K. B., Oh, H. M., Kang, J. G., 2013, Forming Accuracy Comparison Between Positive and Negative Incremental Forming Al 1050, J. Korean Soc. Manuf. Technol. Eng., 22:5 800-805
4. Kim, J. M., Byeon, K. T., Lee,C. S., 2015, A Study for the Improvement of Free-form Surface Formability of CNC Incremental Forming in the Sheet Metal, Proc. Korean Soc. Manuf. Technol. Eng. Spring Conf.,187.
5. Shim, M. S., Park, J. J., 2001, Deformation Characteristics in Sheet Metal Forming with Small Ball, Trans. Mater. Process., 10:1 59-66.
6. Kang, J. G., Choi, D. W., 2006, Contouring Tool Path Generation for Dieless CNC Forming using STL Offset, J. Korean Soc. Precis. Eng., 23:2 191-198.
7. Song, J. Y., 2013, A Study on the Incremental Forming Dimensional Accuracy Using Design of Experiment, Master Thesis, Kyungnam University, Republic of Korea.
8. Choi, D. W., 2004, Dieless CNC Forming System Based on Maching Center, Master Thesis, Kyungnam University, Republic of Korea.
9. Kumar Y., Kumar S., 2015, Incremental Sheet Forming (ISF), Advances in Material Forming and Joining, 29-46.
10. Moser, N., Pritchet, D., Ren, H., Ehmann, K. F., and Cao, J.. 2016, An Efficient and General Finite Element Model for Double-Sided Incremental Forming, ASME. J. Manuf. Sci. Eng., 138:9 091007
11. WIKAN, viewed 18 May 2021, User Manual-R01, <http://wikan.co.kr/front/php/b/board_list.php?board_no=7>.

Seong Ju Choi

Ph.D. candidate in the Department of Mechanical Convergence Engineering, Kyungnam University.His research interest is manufacturing process.

E-mail: pstcsj@hanmail.net

Jae Gwan Kang

Professor in the School of Mechanical Engineering, Kyungnam University.His research interest is CAD/CAM.

E-mail: jkkang@kyungnam.ac.kr

Chai Hwan Kim

Professor in the School of Mechanical Engineering, Kyungnam University.His research interest is materials science and engineering.

E-mail: na48th@kyungnam.ac.kr