한국생산제조학회 학술지 영문 홈페이지

Journal Archive

Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 31 , No. 1

[ Papers ]
Journal of the Korean Society of Manufacturing Technology Engineers - Vol. 31, No. 1, pp. 41-47
Abbreviation: J. Korean Soc. Manuf. Technol. Eng.
ISSN: 2508-5107 (Online)
Print publication date 15 Feb 2022
Received 08 Nov 2021 Revised 14 Dec 2021 Accepted 15 Dec 2021
DOI: https://doi.org/10.7735/ksmte.2022.31.1.41

비등방성 로킹을 위한 금속의 하이브리드 마이크로 텍스쳐링 가공법
박종욱a, * ; 김한b

Hybrid Micro Texturing on Metal Surfaces for Anisotropic Locking
Jong Wuk Parka, * ; Haan Kimb
aDepartment of Mechanical Design Engineering, Dongyang Mirae University
bDepartment of Mechanical Engineering, Dongyang Mirae University
Correspondence to : *Tel.: +82-2-2610-1763 E-mail address: jongwukpark@dongyang.ac.kr (Jong Wuk Park).

Funding Information ▼

Abstract

In this paper, a novel hybrid micro texturing method that combines laser beam machining and electrochemical etching was suggested. In this new machining process, tungsten anisotropic micro channel that was used for directional locking was fabricated. First, laser beam machining on a tungsten workpiece with tilted condition was adopted to rough texturing. Subsequently, a recast layer with tungsten oxide was generated that covered the original anisotropic channel shape, causing a low surface quality. For this reason, electrochemical etching was carried out to elute the recast layer into electrolyte. Moreover, EDS analysis that observed the atomic distribution of textured micro channel was performed to verify the principle of the suggested hybrid process. In the finally fabricated anisotropic micro channel after the hybrid texturing process, the interlocking force (maximum 133.44 N, 5×5 mm2) was measured using the load cell.


Keywords: Laser beam machining, Electrochemical etching, Anisotropic locking, Interlocking, Hybrid machining, Micro texturing

Acknowledgments

이 연구는 동양미래대학교 2019 교내 학술연구 사업의 지원을 받아 수행된 연구임.


References
1. Jung, P. G., Lee, C. H., Bae, K. M., Lee, M. J., Lee, S. M., Lim, C. H., Yun, S. M., Kim, H. K., Ko, J. S., 2010, Microdomegooved Gd2O2S:Tb Scintillator for Flexible and High Resolution Digital Radiography, Opt. Express, 18:14 14850-14858.
2. Manabu, W., Yukihiko, Y., Shuzo, K., Yoshiteru, Y., 2003, Effect of Surface Texturing on Friction Reduction Between Ceramic and Steel Materials under Lubricated Sliding Contact, Wear, 254:3-4 356-363.
3. Chunyong, L., Hongshui, W., Jianjun, Y., Yanli, C., Xin, H., Yang, Y., Baoe, L., Hongjie, L., Haipeng, L., Changyi, L., Xianjing, Y., 2013, Femtosecond Laser-Induced Micropattern and Ca/P deposition on Ti implant Surface and Its Acceleration on Early Osseointegration, ACS Appl. Mater. Interfaces, 5:16 8179-8186.
4. Sanjay, S. L., Chiaki, T., Kazuya, N., Akira, F., 2014, Superhydrophobic Surfaces Developed by Mimicking Hierarchical Surface Morphology of Lotus Leaf, Molecules, 19:4 4256-4283.
5. Czerwinski, F., 2021, Current Trends in Automotive Lightweighting Strategies and Materials, Materials, 14:21 6631.
6. Eid, S. E., Sham Dol, S., 2019, Design and Development of Lightweight-High Endurance Unmanned Aerial Vehicle for Offshore Search and Rescue Operation, 2019 Advances in Science and Engineering Technology International Conference (ASET), UAE 1-5.
7. Kellar, A., Yching, A. L., Hsieh, S. T., Zesch, W., Chan, W. P., Kenny, T. W., Fearing, R., Full, R. J., 2000, Adhesive Force of a Single Gecko Foot-hair, Nature, 405 681-685.
8. Pang, C. H., Kim, S. M., Rahmawan, Y., Suh, K. Y., 2012, Beetle-Inspired Bidirectional, Asymmetric Interlocking Using Geometry-Tunable Nanohairs, ACS Appl. Mater. Interfaces, 4:8 4225-4230.
9. Menciassi, A., Gorini, S., Pernorio, G., Liu, W., Valvo, F., Dario, P., 2004, Design, Fabrication and Performances of a Biomimetic Robotic Earthworm, IEEE International Conference on Robotics and Biomimetics, 274-278.
10. Park, J. W., 2020, Fabrication of Flexible Base Micro-pin Array and Wall Attachment Application, Int. J. Precis. Eng. Manuf., 21 787-795.
11. Cho, S. K., Yang, Y. S., Noh, Y. J., 2008, The Effect of Residual Stress on Fracture Behavior in the Laser Weldment, Laser Solutions, 11:2 1-7.

Jong Wuk Park

Professor in the Department of Mechanical Design Engineering, Dongyang Mirae University. His research interest is non-traditional machining.

E-mail: jongwukpark@dongyang.ac.kr

Haan Kim

Professor in the Department of Mechanical Engineering, Dongyang Mirae University. His research interest is non-traditional machining.

E-mail: haan86@dongyang.ac.kr